Yamaha Amp Editor Uživatelský manuál stáhnout pdf (Strana 204)

Amp Editor Owner’s Manual

204

Appendix

Alert message list

Alert messages that can be specified on the TXn, ACD1, and XMV, their content, and the appropriate responses,

are listed below.

“Single” will appear when an alert event occurs. “Continual” will appear when an alert event occurs and ends.

Some alert messages are displayed in Amp Editor. However, no alert messages are displayed on the ACD1 and the XMV.

If the problem is not solved, please contact your Yamaha dealer.

TXn

ACD1

XMV

Message

(shown in

Amp Editor)

Message

(shown on

TXn/ACD1)

Alert number

(shown on

XMV)

Content Response Initial type

Single/

Continual

Device problem

System error System error 001

The device has not started

up correctly.

Turn the power off, then turn on

after waiting at least 6 seconds. If

this does not solve the problem,

please initialize the memory.

Should this also fails, contact

your Yamaha dealer.

Fault Continual

—— 

Sub CPU Comm

error

—002 Fault Continual

—

Flash ROM

device error

Flash ROM

error

— Fault Single

——  003 Fault Continual

—

No current scene

found

Current scn lost —

The current scene settings

saved in internal memory

have been lost.

Recall the scene. If this does not

solve the problem, contact your

Yamaha dealer.

Fault Single

—— 

No current

preset found

—016

A memory problem has

occurred.

Contact your Yamaha dealer. Fault Continual

—

Resume data

lost

Resume data

lost

—

The settings saved in

internal memory have

been lost.

Either the internal backup battery

has run low, or the device has

malfunctioned.

If a problem persists even after a

scene or preset is recalled,

consult your nearest Yamaha

dealer.

Fault Single

——  015 Fault Continual

 — — DSP error DSP error —

A problem has occurred in

the internal DSP.

It is likely that the device has

malfunctioned; immediately stop

using the device and contact

your Yamaha dealer.

Fault Continual

—— 

DSP hardware

error

—007

The device has not started

up correctly.

Turn the power off, then turn on

after waiting at least 6 seconds. If

this does not solve the problem,

please initialize the memory.

Should this also fails, contact

your Yamaha dealer.

Fault Continual

—

Saving failed Saving failed

— Fault Single

——  004 Fault Continual



Illegal MAC

address

Ille

gal MAC adr 005 Fault Continual



Network

hardware error

Network HW

error

006 Fault Continual

—— 

Dante hardware

error

—008 Fault Continual

No battery No battery 010

The internal backup

battery has been

completely exhausted or is

not installed.

When you turn off the power, the

current settings will be lost, and

will return to the default values.

Please stop use immediately,

and contact your Yamaha dealer.

Fault Continual

Critical battery Critical battery 011

The internal backup

battery has run extremely

low, and it is possible that

the internal memory has

been cleared.

Error Continual

Low battery Low battery 012

The internal backup

battery has only a small

amount of power

remaining.

This does not affect the operation

of the device. However, if you

continue using the device, the

settings may be lost and reset to

the default values. Contact your

Yamaha dealer as soon as

possible.

Warning Single

1 2 ... 199 200 201 202 203 204 205 206 207 208 209 210 211

Komentáře k této Příručce

Žádné komentáře

Yamaha Amp Editor Uživatelský manuál Strana 204

Komentáře k této Příručce

Související produkty a manuály pro Software Yamaha Amp Editor