Yamaha S90 Uživatelský manuál stáhnout pdf (Strana 40)

(3-3) REGISTERED PARAMETER NUMBER

STATUS 1011nnnn(BnH) n = 0~15 CHANNEL NUMBER

LSB 01100100(64H)

RPN LSB 0ppppppp

p = RPN LSB (Refer to the table as shown below)

MSB 01100101(65H)

RPN MSB 0qqqqqqq

q = RPN MSB (Refer to the table as shown below)

DATA ENTRY MSB 00000110(06H)

DATA VALUE 0mmmmmmm m = Data Value

DATA ENTRY LSB 00100110(26H)

DATA VALUE 0lllllll l = Data Value

First, designate the parameter using RPN MSB/LSB numbers. Then, set its value with data entry MSB/LSB.

RPN D.ENTRY

LSB MSB MSB LSB PARAMETER NAME DATA RANGE

00H 00H mmH --- PITCH BEND SENSITIVITY 00H - 18H (0 - 24 semitones)

01H 00H mmH llH MASTER FINE TUNE {mmH,llH}={00H,00H}-{40H,00H}-{7FH,7FH}

(-8192*100/8192) - 0 - (+8192*100/8192)

02H 00H mmH --- MASTER COARSE TUNE 28H - 40H - 58H (-24 - 0 - +24 semitones)

7FH 7FH --- --- RPN RESET

RPN numbers will be left not designated.

The internal values are not affected.

(3-4) NON-REGISTERED PARAMETER NUMBER

There are no applicable parameters.

These are transmitted to the Plug-in board.

(3-5) SYSTEM REAL TIME MESSAGES

(3-5-1) ACTIVE SENSING

STATUS 11111110(FEH)

Transmitted at every 200 msec.

Once this code is received, the instrument starts sensing. When no status nor data is received for over approximately

350 ms, MIDI receiving buffer will be cleared, and the sounds currently played and the sustain switch are forcibly

turned off. In this case, each control data will be reset to a certain value.

(3-6) SYSTEM EXCLUSIVE MESSAGE

(3-6-1) UNIVERSAL NON REALTIME MESSAGE

(3-6-1-1) GENERAL MIDI MODE ON

F0H 7EH 7FH 09H 01H F7H

Received only when the SEQ PLAY MODE is selected.

(3-6-1-2) IDENTITY REQUEST (Receive only)

F0H 7EH 0nH 06H 01H F7H ("n" = Device No. However, this instrument receives under

"omni.")

(3-6-1-3) IDENTITY REPLY (Transmit only)

F0H 7EH 7FH 06H 02H 43H 00H 41H ddH ddH 00H 00H 00H 7FH F7H

dd;Device Number Code

S90: 05 2A

(3-6-2) UNIVERSAL REALTIME MESSAGE

(3-6-2-1) MIDI MASTER VOLUME

F0H 7FH 7FH 04H 01H llH mmH F7H

Sets the MASTER VOLUME value.

The value "mm" is used to set the master volume (the value "ll" should be ignored).

(3-6-3) PARAMETER CHANGE

(3-6-3-1) XG SYSTEM ON

11110000 F0 Exclusive status

01000011 43 YAMAHA ID

0001nnnn 1n Device Number

01001100 4C Model ID

0aaaaaaa 00 Address High

0aaaaaaa 00 Address Mid

0aaaaaaa 7E Address Low

00Data

11110111 F7 End of Exclusive

Received only when the SEQ PLAY MODE is selected.

Be aware that executing this message takes ca. 170ms and that, therefore, a certain interval before executing the

following message is needed.

(3-6-3-2) NATIVE PARAMETER CHANGE, MODE CHANGE

11110000 F0 Exclusive status

01000011 43 YAMAHA ID

0001nnnn 1n Device Number

01101011 6B Model ID

0aaaaaaa aaaaaaa Address High

0aaaaaaa aaaaaaa Address Mid

0aaaaaaa aaaaaaa Address Low

0ddddddd ddddddd Data

11110111 F7 End of Exclusive

For parameters with data size of 2 or more, the appropriate number of data bytes will be transmitted.

See the following MIDI Data Table for Address and Byte Count.

Always received no matter which device number is selected, in the case of REMOTE SWITCH.

(3-6-4) BULK DUMP

11110000 F0 Exclusive status

01000011 43 YAMAHA ID

0000nnnn 0n Device Number

01101011 6B Model ID

0bbbbbbb bbbbbbb Byte Count

0aaaaaaa aaaaaaa Address High

0aaaaaaa aaaaaaa Address Mid

0aaaaaaa aaaaaaa Address Low

00Data

0ccccccc ccccccc Check-sum

11110111 F7 End of Exclusive

See the following MIDI Data Table for Address and Byte Count.

The Check sum is the value that results in a value of 0 for the lower 7 bits when the Byte Count, Start Address, Data

and Check sum itself are added.

(3-6-5) DUMP REQUEST

11110000 F0 Exclusive status

01000011 43 YAMAHA ID

0010nnnn 2n Device Number

01101011 6B Model ID

0aaaaaaa aaaaaaa Address High

0aaaaaaa aaaaaaa Address Mid

0aaaaaaa aaaaaaa Address Low

11110111 F7 End of Exclusive

See the following MIDI Data Table for Address and Byte Count.

(3-6-6) PARAMETER REQUEST

11110000 F0 Exclusive status

01000011 43 YAMAHA ID

0011nnnn 3n device Number

01101011 6B Model ID

0aaaaaaa aaaaaaa Address High

0aaaaaaa aaaaaaa Address Mid

0aaaaaaa aaaaaaa Address Low

11110111 F7 End of Exclusive

See the following MIDI Data Table for Address and Byte Count.

(4) SYSTEM OVERVIEW (Keyboard, Sequencer and Tone

Generator)

The optional mLAN board can be installed to the S90.

Although three types of note on/note off data, received via MIDI, played by the internal sequencer and played on the

keyboard will be distinguished, the other controllers (channel messages) equally affect the entire notes.

ALL SOUND OFF clears all the sounds in the specific channel(s) played by both the keyboard and the data via MIDI.

ALL NOTES OFF received via MIDI clears the sounds in the specific channel(s) played via MIDI.

SEQ KBD

MIDI In

MIDI Out

From USB

To USB

Local Sw

USB/MIDI = MIDI

SEQ KBD

MIDI In

MIDI Out

From USB

To USB

Local Sw

Thru Port

USB/MIDI = USB

1 2 ... 35 36 37 38 39 40 41 42 43 44 45 ... 55 56

Komentáře k této Příručce

Žádné komentáře

Yamaha S90 Uživatelský manuál Strana 40

Komentáře k této Příručce

Související produkty a manuály pro Software Yamaha S90