Yamaha S90 Uživatelský manuál stáhnout pdf (Strana 38)

MIDI Data Format

Many MIDI messages listed in the MIDI Data Format section are expressed in hexadecimal or

binary numbers. Hexadecimal numbers may include the letter “H” as a suffix. The letter “n”

indicates a certain whole number. The chart below lists the corresponding decimal number for

each hexadecimal/binary number.For more information, refer to the Owner’s Manual (page 118).

SYNTHESIZER/SEQUENCER PART

(1) TRANSMIT FLOW

MIDI<- +-[SW1]-+-------- NOTE ON/OFF 9nH

OUT | |

| |

| +-------- KEY'S AFTER TOUCH AnH (Seq only)

| |

| +-------- CONTROL CHANGE

| | MODULATION BnH,01H

| | VOLUME BnH,07H

| | PAN BnH,0AH

| | SUSTAIN SWITCH BnH,40H

| | FILTER RESONANCE BnH,47H

| | EG RELEASE TIME BnH,48H

| | EG ATTACK TIME BnH,49H

| | FILTER CUTOFF FREQ BnH,4AH

| | EG DECAY TIME BnH,4BH

| | REVERB SEND BnH,5BH

| | CHORUS SEND BnH,5DH

| | ASSIGNABLE CONTROLLERS BnH,(00H .. 5FH)

| | SEQ REMORT CONTROL BnH,(00H .. 7FH)

| |

| +-[SW7]-- BANK SEL MSB BnH,00H

| | BANK SEL LSB BnH,20H

| |

| +-------- CHANNEL MODE MESSAGE (Seq only)

| | RESET ALL CONTROLLERS BnH,79H

| | LOCAL CONTROL BnH,7AH

| | OMNI MODE OFF BnH,7CH

| | OMNI MODE ON BnH,7DH

| | MONO MODE ON BnH,7EH

| | POLY MODE ON BnH,7FH

| |

| +-[SW8]-- PROGRAM CHANGE CnH

| |

| +-------- CHANNEL AFTER TOUCH DnH

| |

| +-------- PITCH BEND CHANGE EnH

+-[SW4]---------- SYSTEM COMMON MESSAGE

| SONG POSITION POINTER F2H

+-[SW4]---------- SYSTEM REALTIME MESSAGE

| TIMING CLOCK F8H

| START FAH

| CONTINUE FBH

| STOP FCH

+---------------- ACTIVE SENSING FEH

+-[SW5]-+-------- SYSTEM EXCLUSIVE MESSAGE

| +-[SW6]-- <BULK DUMP>

F0H 43H 0nH 6BH bhH blH ahH amH alH ddH... ddH ccH F7H

| |

| +-[SW6]-- <PARAMETER CHANGE> F0H 43H 1nH 6BH ahH amH alH ddH.....ddH F7H

+---------------- SYSTEM EXCLUSIVE MESSAGE

IDENTITY REPLY F0H 7EH 7FH 06H 02H 43H 00H 41H 05H 2AH

00H 00H 00H 7FH F7H

[SW1] MIDI Transmit Channel

In the Master mode: complies with Zone Transmit Channel.

In the mode other than the Master: complies with Keyboard Transmit Channel.

[SW2] MIDI Control Mode

[SW4] Seq MIDI Control

[SW5] MIDI Device Number

When set to all, transmitted via 1.

[SW6] In the Voice mode, only the Voice related data can be transmitted.

In the Performance mode, only the Performance related data can be transmitted.

The System data can be transmitted/recognized in any mode.

[SW7] SYSTEM Bank Select Switch

[SW8] SYSTEM Program Change Switch

(2) RECEIVE FLOW

MIDI>- +[SW10]-+-------- NOTE OFF 8nH

| |

| +-------- NOTE ON/OFF 9nH

| |

| +-------- CONTROL CHANGE

| | MODULATION BnH,01H

| | PORTAMENTO TIME BnH,05H

| | DATA ENTRY MSB BnH,06H

| | DATA ENTRY LSB BnH,26H

| | MAIN VOLUME BnH,07H

| | PAN BnH,0AH

| | EXPRESSION BnH,0BH

| | SUSTAIN SWITCH BnH,40H

| | PORTAMENTO SWITCH BnH,41H

| | SOSTENUTO BnH,42H

| | HARMONIC CONTENT BnH,47H

| | EG RELEASE TIME BnH,48H

| | EG ATTACK TIME BnH,49H

| | BRIGHTNESS BnH,4AH

| | EG DECAY TIME BnH,4BH

| | EFFECT1 DEPTH BnH,5BH

| | EFFECT3 DEPTH BnH,5DH

| | DATA ENTRY INC BnH,60H

| | DATA ENTRY DEC BnH,61H

| | ALL SOUND OFF BnH,78H

| | ASSIGNABLE CONTROLLER BnH,(00H .. 5FH)

| | NRPN BnH,62H,63H *2

| | RPN

| | PITCH BEND SENS. BnH,64H,00H,65H,00H,06H,mmH

| | FINE TUNING BnH,64H,01H,65H,00H,06H,mmH,26H,llH *1

| | COARSE TUNING BnH,64H,02H,65H,00H,06H,mmH *1

| | RPN RESET BnH,64H,7FH,65H,7FH

| |

| +-[SW2]-- EG SUSTAIN LEVEL BnH,1FH

| |

| +-[SW7]-- BANK SEL MSB BnH,00H

| | BANK SEL LSB BnH,20H

| |

| +-------- CHANNEL MODE MESSAGE

| | RESET ALL CONTROLLERS BnH,79H

| | OMNI MODE OFF BnH,7CH

| | OMNI MODE ON BnH,7DH

| | MONO MODE ON BnH,7EH

| | POLY MODE ON BnH,7FH

| +-[SW8]-- PROGRAM CHANGE CnH

| |

| +-------- CHANNEL AFTER TOUCH DnH

| |

| +-------- PITCH BEND CHANGE EnH

+-[SW3]-+-------- SYSTEM REALTIME MESSAGE

| TIMING CLOCK F8H

+-[SW4]-+-------- SYSTEM REALTIME MESSAGE

| START FAH

| CONTINUE FBH

| STOP FCH

+---------------- ACTIVE SENSING FEH

+-[SW5]-+-------- SYSTEM EXCLUSIVE MESSAGE

| | MIDI MASTER VOLUME

F0H 7FH 7FH 04H 01H llH mmH F7H

| |

| +-[SW9]-- <BULK DUMP>

F0H 43H 0nH 6BH bhH blH ahH amH alH ddH....ddH ccH F7H *3

| |

| +-[SW6]-- <PARAMETER CHANGE>

F0H 43H 1nH 6BH ahH amH alH ddH.....ddH F7H *3

| |

| +-[SW6]-- <BULK DUMP REQUEST>

F0H 43H 2nH 6BH ahH amH alH ddH.....ddH F7H *3

| |

| +-[SW6]-- <PARAMETER REQUEST> F0H 43H 3nH 6BH ahH amH alH F7H *3

| |

| +-[SW11]- XG SYSTEM ON F0H 43H 1nH 4CH 00H 00H 7EH 00H F7H

| |

| +-[SW11]- GM MODE ON F0H 7EH 7FH 09H 01H F7H

+---------------- SYSTEM EXCLUSIVE MESSAGE

IDENTITY REQUEST F0H 7EH 0nH 06H 01H F7H

[SW2] MIDI Control Mode

[SW3] MIDI Sync (can be set to "internal", or "MIDI")

[SW4] Seq MIDI Control

[SW5] MIDI Device Number

When this is not set to off, the MIDI Master Volume can be recognized in any mode.

[SW6] In the Voice mode, only the Voice related data can be transmitted.

In the Performance mode, only the Performance related data can be transmitted.

The System data can be transmitted/recognized in any mode.

[SW7] SYSTEM Bank Select Switch

[SW8] SYSTEM Program Change Switch (In the Voice mode, recognized only in the play mode.)

[SW9] SYSTEM Bulk Protect and same as SW6.

[SW10] MIDI Receive Channel

In the Mixing mode: complies with Part Receive Channel and Part Receive Switch.

In the other mode: complies with Basic Receive Channel.

[SW11] SYSTEM Receive GM/XG On

*1: Mixing Mode Only

*2: Available only for the Plug-in voices

*3: The messages of Plug-in Voice (MODEL ID = 64H) can be recognized/transmitted.

1 2 ... 33 34 35 36 37 38 39 40 41 42 43 ... 55 56

Komentáře k této Příručce

Žádné komentáře

Yamaha S90 Uživatelský manuál Strana 38

Komentáře k této Příručce

Související produkty a manuály pro Software Yamaha S90