Yamaha RX-300 Uživatelský manuál

OWNER’S MANUALNatural Sound AV ReceiverRX-V300KThank you for selecting this YAMAHA AV receiver.R

8CONNECTING SPEAKERSREAR REARCENTERCAUTION SEE INSTRUCTION MANUAL FOR CORRECT SETTING. MAINSPEAKERSABREARSINGLESINGLE:6ΩMIN. /SPEAKER:3ΩMIN. /SPEAKER

9EnglishFor connecting to the MAIN SPEAKERS terminalsRed: positive (+)Black: negative (–)➀Unscrew the knob.➁Insert the bare wire.[Remove approx. 5mm(1

10Be sure to switch this only when the power of this unit is turnedoff. Select the position whose requirements your speaker systemmeets.WARNINGDo not

11EnglishANTENNA CONNECTIONS●Each antenna should be connected to the designated terminals correctly, referring to the following diagram.●Both AM and F

12CONTROLS AND THEIR FUNCTIONSFRONT PANELPOWERSPEAKERSPHONESAONBOFFBASS TREBLE BALANCEVOLUME55432l0l23455432l0l234LRl620284060l28420–dB55432l0l234FM/A

13EnglishB PHONES jackWhen you listen with headphones, connect the headphones to the PHONES jack. You can listen to the sound to be output from the ma

For Control of This Unit1 DELAY/KEY and TIME/KEY – ( )/+ ( ) keysAdjust the delay time (DELAY) and key level of the currentlyplaying tune (KEY).

15EnglishNotes about the remote control transmitterBattery installationBattery replacementIf you find that the remote control transmitter must be used

16DISPLAY PANELPRESETkHzMHzMEMORY AUTO TAPE MONSTEREO020l00msPRO LOGIC3 STEREO HALLVOCAL AIDLIVE HOUSEONE TOUCH KARAOKESLEEP NORMAL WIDEPHANTOMEFFECT

17English1Set to the “∞” position.2 Turn the power on.3 Select the main speakers to be used.* If you use two main speaker systems, press both the Aand

1 Read Instructions – All the safety and operatinginstructions should be read before the unit is operated.2 Retain Instructions – The safety and oper

7 Turn up the volume.You will hear a test tone (like pink noise) from the left mainspeaker, then the center speaker, then the right mainspeaker, and t

19English1Set to the “∞” position.2 Turn the power on.3 Select the desired input source by using the inputselector buttons.(For video sources, turn th

201 Select the source to be recorded.2 Play the source and then turn the VOLUME control upto confirm the input source. (For detailed informationon th

21EnglishSelecting the SPEAKER systemBecause one or two speaker systems (as main speakers) canbe connected to this unit, the SPEAKERS switches allow y

221 Select “TUNER” as the input source. 2 Select the reception band (FM or AM) confirming it onthe display. 34 Tune to a desired station manually. * T

23English1 Tune to a desired station.(Refer to the previous page for tuning procedure.)2 Select a desired group (A – E) of preset stationsconfirming i

24123To tune to higher frequencies, press right side once.To tune to lower frequencies, press left side once.* If the TUNING button is not pressed, in

25EnglishEXCHANGING PRESET STATIONSYou can exchange the places of two preset stations with each other as shown below.Example)If you want to shift the

26FEATUREThis program is used for playback of sources encoded with Dolby Surround.The application of a sophisticated digital signal processing system

27English1 Follow steps 1 – 6 shown in “BASIC OPERATIONS” onpage 19.2 Select the desired program that is suitable for thesource.The selected program n

1EnglishNote to CATV system installer:This reminder is provided to call the CATV systeminstaller’s attention to Article 820-40 of the NEC thatprovides

28Adjustment of the CENTER LEVEL Adjustment of the REAR LEVELIf desired, you can adjust the sound output level of the centerspeaker even if the output

1 Connect one or two microphones to the MIC jack(s) onthe front panel.2 Follow steps 1 to 7 of “BASIC OPERATIONS” on page19.3 Select a desired DSP pro

Turning the MIC LEVEL control clockwise increases the level,and counterclockwise decreases the level.Turning the ECHO level control clockwise increase

31EnglishAdjusting key of the tune currently playingRecording your vocal mixed with the source onto a tape (adding effects of a selected DSP program f

321Whenever the SLEEP key is pressed, the SLEEP time willchange as follows.After a while, the display returns to the indication beforethe SLEEP timer

33EnglishIf the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simplemeasures sugge

34AUDIO SECTIONMinimum RMS Output Power per ChannelMain L, R8 ohms, 20 Hz to 20 kHz, 0.04% THD[U.S.A. model]...60W + 60W[Singap

35EnglishAM SECTIONTuning Range[U.S.A. and General models]...530 to 1,710 kHz[Singaporemodel]...

VY88670YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.YAMAHA CANADA MUSIC LTD. 135 MILNER AV

2Safety Instructions ...Inside the Front CoverSupplied Accessories ...2Features ...

3English●5 Speaker Configuration<U.S.A. model>Main: 60W + 60W (8Ω) RMS OutputPower, 0.04% THD, 20–20,000 HzCenter: 60W (8Ω) RMS Output Power, 0.

41. To assure the finest performance, please read this manualcarefully. Keep it in a safe place for future reference.2. Install this unit in a cool,

5EnglishPROFILE OF THIS UNITYou are the proud owner of a Yamaha AV receiver — an extremely sophisticated audio component. The Digital Sound FieldProc

6SPEAKER SETUPSPEAKERS TO BE USEDThis unit is designed to provide the best sound-field quality with a 5 speaker configuration. The most effective spe

7EnglishCONNECTIONSNever plug in this unit and other components until all connections are completed.CONNECTIONS WITH OTHER COMPONENTSWhen making conne