DPX-830Digital Cinema ProjectorProjecteur Cineme NumeriqueOWNER’S MANUALMODE D’EMPLOIBEDIENUNGSANLEITUNGMANUALE DI ISTRUZIONIMANUAL DE INSTRUCCIONESBR
6◆ Remote control overview1. IR signal transmitter2. ON ( I ) button3. AUTO button4. NORMAL button5. HDMI button6. D-SUB button7. Cursor buttons ( / /
7◆ Operational rangeOperate the remote control within a distance of 10 m from the projector, pointing the light beam at the remote control sensor (fro
8◆ Setting up the screenInstall the screen perpendicularly to the projector. If the screen can not be installed in such a way, adjust the projection a
9◆ Mounting the projector on the ceilingTo view images projected by the ceiling mounted projector from the front:When the projector is installed on th
10◆ Screen size and projection distanceRefer to the following diagram to determine the screen size.When the aspect ratio of the screen is 16:9• The ab
11◆ Basic home theater system connectionImportant• Make sure that the power of the projector and that of the video equipment are turned off.• Connecti
12◆ Connecting to a video player, etc.Using the VIDEO terminal1. Connect one end (yellow) of a commercially available video cable to the VIDEO input t
13◆ HDMI or DVI connectionsYou can project high-quality images by connecting the HDMI input terminal of this projector to video equipment having a HDM
14◆ Connecting to a computerImportant• Make sure that the power of the projector and that of the computer are turned off.• When connecting the project
15◆ TRIGGER terminalThe TRIGGER terminal on the rear of the projector is a terminal that outputs 12 V signal to control an externally connected equipm
iIMPORTANT SAFETY INSTRUCTIONS• Explanation of Graphical SymbolsThe lightning flash with arrowhead symbol, within an equilateral triangle, is intended
16◆ Viewing video imagesPreparation:• Always remove the lens cap before operating the projector.• Turn on the power of the connected video equipment.1
17To stop projecting:1. Press the STANDBY/ON () button on the projector or the STANDBY ( ) button on the remote control.• A confirmation message is di
18Examples of the aspect ratioYou can change the aspect ratio of the input video signal (or the ratio of width to height of the image). Display patter
19◆ Viewing computer imagesPreparation:• Always remove the lens cap before operating the projector.• Turn on the power of the connected computer.1. Co
20To stop projecting:1. Press the STANDBY/ON () button on the projector or the STANDBY ( ) button on the remote control.• A confirmation message is d
21◆ Menu overviewMenus are not displayed when no signal is received by the projector.After selecting the items marked with , press the ENTER button.*
22How to set the menusFollowing describe how to set AUTO POWER OFF time as an example.1. Press the MENU button.• If no signal is input, the menu does
23◆ Menu settingsThe following items in the menus enable you to customize this projector.1. IMAGE menu• DEFAULT depends on the two signal types below:
242. SETUP menu• Do not change the setting of the LAMP MODE frequently. This could damage the lamp. • To exit from the TEST PATTERN, press any buttons
253. INITIAL menu• DEFAULT depends on the two signal types below:1. Video signals (TV50, TV60, 480i/p, 576i/p, 720p50/60, 1080i50/60)2. Computer signa
iiCOMPLIANCE INFORMATION STATEMENT(DECLARATION OF CONFORMITY PROCEDURE)Responsible Party: Yamaha Electronics CorporationAddress: 6660 Orangethorpe Ave
264. SIGNAL menu* The default value and the setting range differ depending on the input signals.• Horizontal strips may appear on the enlarged project
27◆ Selecting the gamma mode (GAMMA)You can select a preset gamma mode by using the menu (see page 23). 1. Display the IMAGE menu.2. Select GAMMA by p
28◆ Selecting the color temperature (COLOR TEMP.)You can select a preset color temperature (white tone) using the menu (see page 23).1. Display the IM
29◆ Adjusting color (SATURATION and HUE)You can adjust the color of the projected image using the menu (see page 23).1. Display the IMAGE menu.2. Sele
30◆ Saving memory settingsThe memory function saves up to 3 patterns of the image quality settings for each input source. Following is the list of ite
31This projector automatically and properly projects video signals supplied from the computer. However, some video signals may not be projected depend
32This projector is equipped with a lamp to project images. This lamp is a consumable, so it may burn out or its brightness may decrease during use. I
33◆ Replacing the lampWarning• Do not replace the lamp immediately after using the projector because the lamp would be extremely hot and it may cause
34◆ Attaching a commercially available lens filter1. Carefully turn the projector upside-down.2. Loosen the screw (a) using a Phillips screwdriver (+)
35◆ TroubleshootingRefer to the chart below when this projector does not function properly. If the problem you are experiencing is not listed below or
iiiCaution: Read this before operating this unit.Warning• This unit must be grounded• Do not use this projector in a computer roomThis projector is no
36Images are not displayed correctly.“NO SIGNAL” is displayed. • Turn on the power of the connected equipment, or check whether there is something wro
37OthersIf the following problem occurs after the lamp is replaced, check the following first.Problem SolutionThe exhaust vents emit warm air.• This a
38This projector has two indicators, each of which shows the operation condition of the projector.Refer to Troubleshooting for additional indication s
39◆ Projector specificationsThe specifications and outside appearance of the projector are subject to change without prior notice.Type DLP™ projectorM
40◆ Composite / S-video signal specificationsSignal mode Resolution (H × V)Horizontal frequency (kHz)Vertical frequency (Hz)Default mode for 16:9 scre
41*1: When ASPECT in the INITIAL menu is set to DEFAULT, and SCREEN ASPECT in the SETUP menu is set to 16:9.*2: When ASPECT in the INITIAL menu is set
11 Getting started 2Inappropriate places for installation ...2Accessory check ...3Ins
2◆ Inappropriate places for installationIf this unit is not correctly installed in an appropriate place, it may cause fire or failure, or damage the u
3◆ Accessory checkThe following accessories are provided with this projector. Check to be sure that all of the accessories are packed in the package.I
4◆ Inserting the batteries into the remote control1. Remove the rear lid of the remote control.2. Check the polarity markings (+, –) of the batteries,
5◆ Projector overview1. FOCUS ring2. ZOOM ring3. Control panel 4. Air intake vent5. Remote control sensor (Front)6. Air intake vent7. Air exhaust vent
Komentáře k této Příručce