Yamaha DTR2 Uživatelský manuál

YAMAHAProfessional Series Digital Audio Tape RecorderOWNER'S MANUALMODE D'EMPOlBEDIENUNGSANLEITUNG

Connecting an analog audio componentCONNECTIONS••Be sure to disconnect the power cords of bothcomponents from the AC outlet before connecting.The same

Connecting to another digital audio tape deck, or an amplifier, etc. which has digital jacksWhen this unit is connected to another DAT deck,amplifier

Connecting the remote control transmitterBy connecting the remote control cable to the REMOTE jack on the rear panel, this unit can be operated with t

DAT (Digital Audio Tape)DAT cassettesA DAT cassette measures 2-7/8" x 7/16" x 2-1/8" (73 mm x10.5 mm x 54 mm), nearly half the size of

Preventing accidental erasureTo prevent accidental erasure, slide the tab to the left toopen the hole. The tape cannot be recorded even if theREC butt

LOADING AND UNLOADING CASSETTESLoading a cassette1 Turn the POWER switch ON.2 Press the OPEN/CLOSE buttonto open thecassette holder."OPEN" f

RECORDINGIntroduction to DAT recordingUnlike ordinary audio cassette tapes, various control codescalled subcodes can be written on the DAT cassette ta

Recording from the analog input jacksThis procedure is recommended when making a recordingfrom a mixing console, analog tape deck, tuner,phonograph or

To stop recording temporarily1 Press the PAUSE buttonRecording stops temporarily.2 Press the PLAY button or PAUSE buttonagain to resume recording.When

START ID SIGNALS AND TUNE NUMBERSThe actual number of a recorded tune on a tape and thetune number displayed on the unit may not be the same,even if t

Thank you for purchasing the YAMAHA DTR2 Digital Audio Tape Recorder.SAFETY INSTRUCTIONSCAUTION: TO REDUCE THE RISK OF ELECTRICSHOCK, DO NOT REMOVE CO

Notes on writing start ID signalsIf a start ID signal is written on a point where a skip IDsignal has been written, the skip ID signal is erased.The i

To continue a recording from the end of aprevious recording1 Press the END ID SEARCH button in stop mode orduring playback.The button starts flashing.

PLAYBACKNormal playback1 Load the tape into the cassette holder.2 Press the PLAY button22To stop playback1 Press the STOP button2 To start playback ag

APSS (Auto Program Search System)APSS allows you to locate the beginning of any tune duringplayback. Simply press the REW or FF b

You can program desired tunes in any desired order.To program desired tunes (APMS=Automatic Programmable Music Selector)If the tunes are not numbered

Direct selectionAny tune can be directly selected and played back byspecifying the tune number.In stop mode or play mode, enter the desired tunenumber

26Cue and reviewThe CUE and REVIEW buttons allow you to quickly move toa desired location on the tape while listening to the tunes at3 times the speed

To skip undesirable sections-using the skip IDWhen the unit encounters a skip ID signal, the tape fast-forwards to the beginning of the next tune.To w

28To display elapsed time and the tape counterEach time the DISPLAY button is pressed during playback,the display changes to 1, 2, or 3, in that order

If this unit functions abnormally during operation, first check the following items. If the unit continues to function abnormally, orif an abnormality

CAUTION: READ THIS BEFORE OPERATINGYOUR UNIT.1. This unit is a sophisticated digital audio tape recorder. Toensure proper operation for the best possi

SPECIFICATIONSDAT system Rotary head type digital audio tape recorderLoading system Horizontal front loadingRecording system Serial Copy Management Sy

This product complies with the radio frequency interferencerequirements of the Council Directive 82/499/ECC and /or87/308/EEC.

YAMAHASERVICEThis product is supported by Yamaha's worldwide network offactory trained and qualified dealer service personnel.In the event of a p

TABLE OF CONTENTSFeatures4Names of controls5Connections10DAT (Digital Audio Tape)13Loading and unloading cassettes15Recording16Start ID signals and tu

NAMES OF CONTROLSFront panelPOWER switchTurns the power on and off.Cassette holderHolds the digital audio tape.INPUT selectorSet to DIGITAL to record

START ID buttonsAUTO WRITE: Press to automatically write the start IDsignals and their tune numbers during recording.WRITE: Used to write the start ID

Display windowRemote control transmit indicatorLights when the remote control transmitter is operated.TOC (Table of Contents) indicatorLights when a t

Rear PanelNAMES OF CONTROLSANALOG INPUT jacks (unbalanced type pin-jacks)When these jacks are used for recording, adjust theinput level with the REC L

Wired remote control transmitterStart ID buttonsSkip ID buttonsEnd ID buttonsClear buttonProgram buttonRepeat buttonOpen/close buttonStop buttonPlay b